WeldCyprus
ALL CYPRUS // STEEL 3 · 4 · 6 MM

A steel BBQ
thick plate
that heat cannot warp.

Grill width from 60 centimetres to a metre and a half, in 3, 4 or 6 mm steel. Open, with a lid, or with a chimney when the smoke bothers the neighbours or drifts into the pergola.

UP TO 6 MM STEEL WITH A LID WITH A CHIMNEY SIDE TABLE WHEELS
Welder in a mask making a TIG weld on a steel box section, close-up
from €400
PER GRILL
7
WORKING DAYS
6 mm
THICKEST PLATE
60–150
CM GRILL WIDTH

Worth deciding before you order

/ 01

Plate thickness is service life

Two-millimetre sheet warps by the third fire: the walls bow out and the lid stops closing. 3 mm is the minimum for a holiday house, 4 mm is the working thickness, and 6 mm holds its shape for years and heats evenly — but two people can no longer carry it.

/ 02

Lid and chimney

A lid holds the heat and lets you roast rather than only grill. A chimney matters when the grill stands against the house wall, under a canopy, or close to a neighbour window: without one the smoke goes where people sit.

/ 03

There is no coating inside

The inside is never painted or galvanised — at four hundred degrees any coating burns off and ends up in the food. Heat-resistant enamel goes on the outside; inside it is bare steel that scorches on the first fire and works as it is from then on.

Build it to your size

Pick the width, the plate thickness and the type — the price follows. The configuration stays in the page address, ready to save or send to me.

Typical configurations and prices

Why the price here is approximate

What the page works out is an estimate, not a quote. The final figure is always worked out separately, because the same structure in two different places does not cost the same.

  • How easy the spot is to reach, and whether the van and the gear fit.
  • What it stands on and bolts to: wall, concrete, roof, soil — the condition of the base changes the job.
  • Where reinforcement is needed and where it can be done more simply — and come out cheaper.
  • How fast you need it, and how much preparing the site takes.

This is not factory production, where everything comes out identical, soulless and at the lowest price. Each piece is made for your particular spot. Write to me — we will go through where reinforcement is worth it and where it is not, and I will find an option that suits you.

SEND THIS CONFIGURATION TO WHATSAPP

More from the catalogue

/ 01 7 working days

Table

A steel frame built for the top you choose: oak, HPL compact, concrete or glass. Galvanised when it lives outdoors.

Oak 40 mm HPL compact 12 mm Concrete over steel Hot-dip galvanised
from €350 CONFIGURE
/ 02 5 working days

Bench

Bench with or without a backrest, timber or checker-plate seat. Pairs with the table or stands alone by the pool.

With backrest Oak Hot-dip galvanised
from €300 CONFIGURE
/ 03 5 working days

Outdoor shower

A shower post by the pool or at the beach house. Galvanised, aluminium or stainless — next to salt water that is not decoration.

Stainless AISI 304 Timber deck Hot-water mixer
from €500 CONFIGURE
/ 04 2 working days

A/C bracket

Bracket for the outdoor unit: up to 12,000, 18,000 BTU or more. With an anti-theft cage if the unit sits on the ground floor.

Hot-dip galvanised Stainless AISI 304 Anti-theft cage
from €150 CONFIGURE
/ 05 4 working days

Solar heater frame

Frame for a 120–200 litre tank, flat roof or pitched. With wind bracing so the winter gusts leave the collector alone.

200 litres Pitched roof Wind bracing
from €350 CONFIGURE
/ 06 4 working days

Roof ladder

Ladder to the roof for the boiler and the aerials: straight, with a safety cage, or with a removable lower section.

With safety cage Hot-dip galvanised Top platform
from €300 CONFIGURE

Frequently asked

What does a made-to-order BBQ cost?
An open 0.8 m grill in 4 mm steel is around €550. The same in 6 mm, around €700. A lid adds roughly a quarter, a chimney about half. A small 0.6 m grill in 3 mm starts at €400.
Is it fixed, or can it be moved?
By default it stands on legs: 4 mm steel on a metre-wide grill is already over fifty kilograms. If it has to move, add wheels in the calculator — two swivelling with brakes, two plain.
Can you make it for a cauldron or a grill grate?
Yes. A cutout for a cauldron, skewer rests, a removable stainless grate — all of it is made to fit. Build the base configuration, then say what you need in the message and I will price it separately.

Order — BBQ grill

How to reach me

Call +357 99 230 862

Fastest way: send a photo of the job to WhatsApp or Telegram — you get a price within the hour.

PHONE / WHATSAPP
+357 99 230 862
TELEGRAM
@welder_cyprus
BASE
Larnaca, Cyprus
Installation across Cyprus
HOURS
Mon–Sat 08:00–20:00